• QT4-26 Brick Making Machine

QT4-26 Brick Making Machine

QT4-26 Brick Making Machine, used the European advanced flat vibration manufacturing technique for reference, with the lower power, realizes the super strong vibration effect, mixing every material effectively.

Specifications:

  • Model: QT4-26
  • Vibration Frequency: 4200 r/min
  • Cycle Time: 26 s
  • Overall Power: 18.5 KW

The introduction of the QT4-26 Brick Making Machine

砖1

QT4-26 small semi-automatic unburned brick machine has strong adaptability and can be used for many purposes. It is not only suitable for producing concrete blocks, but also suitable for producing blocks made of fly ash, slag, slag and other materials, and installing different molds. It can produce strong bricks of various specifications, standard bricks, hollow bricks, porous bricks, etc.

 

The QT4-26 semi-automatic block forming unburned brick machine improves the vibration technology and arch breaking device of the predecessors, realizes the separate control of distribution and forming vibration, and makes the distribution most uniform and shaped.

 

The QT4-26 semi-automatic block forming unburned brick machine is molded and vibrated. However, the concrete can be fully liquefied and exhausted within two to three seconds. The high density of the product is particularly suitable for producing high-strength standard bricks. After forming, it can be stacked, saving a lot of investment in supporting plates.

 

QT4-26 semi-automatic block forming unburned brick machine adopts special double end composite output vibration technology to optimize the arrangement of vibrators, so that the exciting force is evenly distributed in the vibration table.

 

QT4-26 semi-automatic block forming unburned brick machine uses advanced electric control technology, hydraulic system, integrated automatic control, simple operation and integrated automatic control.

1. When installing or replacing new or old molds, be sure to avoid collision and bump, assemble in a civilized manner, and protect the molds.

 

2. Check the size of the mold and the condition of the welding joint frequently during the use. If there is a weld crack, repair it in time. If the wear is too fast, adjust the particle size of the aggregate. If the wear is excessive, affect the product quality, a new mold is required.

 

3. Carefully adjust the clearance, including the distance between the indenter and the mold core, between the indenter and the moving plane of the skip car, between the mold frame and the wire plate. The relative movement shall not interfere with or rub against each other.

 

4. When cleaning the mold daily, use the air compressor and soft tools to remove the concrete residue. It is strictly prohibited to strike or pry the mold by gravity.

 

5. The replaced mold shall be cleaned, oiled and rustproof. It shall be placed in a dry and flat place and supported flat to prevent gravity deformation.

 

 

砖2
砖3

          6. Cleaning. We think it is troublesome to clean many heavy equipment. It is also wrong to think that the equipment hardly needs cleaning because of its bulkiness. Whether the equipment needs cleaning depends on the working conditions. We humans need to take a bath every day when working in a very dirty environment. The same is true for the equipment. We must clean the mold, pump station and power distribution cabinet every day after the production of the cement brick machine.

          7. Before production, please check every part of the cement brick machine, such as the tightness of the screws, the tightness of the motor belt, and the joint of the welding seams.

          8. It is important to note that the mold is an important part of our production, but the mold is easy to wear, although the mold produced by our company has undergone heat treatment. However, please carefully clean the mold after production every day, so as to prolong the life of the mold. The replaced mould shall be oiled and stored after cleaning to ensure the next replacement.

Technical Parameters

Model

QT4-26

Rates Pressure (Mpa)

16

Vibration Frequency (r/min)

4200

Main Vibration Form

 Platform Vibration

Molding Cycle (s)

26

Overall Power (kw)

18.5

Pallet Size (mm)

850* 480*20

Overall Dimension (mm)

2060*1700*2560

 

 

Product Show

图片2
图片2

Case

图片3
图片4
图片5
Write your message here and send it to us

Sale service

Modular design for convenient and fast installation, maintenance, relocation and tranportation.